Can underfloor heating be mounted on a wall?
You can install a heated floor on any plane, including on a wall or ceiling, but to do this, the structure must be securely fastened and a channel for the power cable must be laid. At the same time, the heat transfer efficiency does not decrease depending on its location.
This placement option is suitable if it is not possible to install heating radiators, and installation of a heating electric or water floor is not possible. An example of such a room is a flight of stairs.
In addition, heating installed in this way will cut off cold air, which is especially important if the wall is outdoor. But it is worth noting that some of the heat will still be wasted, heating the street. Therefore, it is necessary to make a good thermal insulation layer to reduce heat loss.
Expert opinion
It-Technology, Electrical power and electronics specialist
Ask questions to the “Specialist for modernization of energy generation systems”
Heater TeplEko Quartz - “How to install? Is it economical? Is it safe for children and animals? Minimum working equipment. What do you need to buy in addition, and what can you do without? Advantages and disadvantages. Will a woman be able to install it? » | reviews Here we leave the choice of convector control up to you, since in the future, you can always buy an additional socket with a thermostat and expand the capabilities of your inexpensive device. Ask, I'm in touch!
Connection diagram
Water convectors are specialized equipment, so their installation is best left to professionals, especially when it comes to installing in-floor or basement types. You are only allowed to install wall-mounted water convectors yourself. In this case, it is necessary to follow a strict sequence of actions.
- It is necessary to mark the wall - using a level to determine the location of the convector itself, the place of water connection and, if necessary, electricity. Here you can either attach the radiator itself to the wall, or make markings with a ruler using the data in the product passport.
- Then the wall is drilled according to the applied markings and screwed into the dowel holes.
- Carry out the installation of pipes and electrical cables.
- The back of the convector is screwed to the wall with screws that are included in the kit. In this case, first they simply attach it to the screws, then measure the accuracy of fastening with a level, and only when they are convinced of this, screw the installation panel to the end.
- Now you need to secure the heat exchanger unit to the installation panel. For this purpose, it is allowed to use only those screws and fasteners supplied by the manufacturer.
- Now the electricity cable is connected to the terminal box. In this case, the main connection parameters are the manufacturer’s instructions and electronic circuit diagram. You must act strictly in accordance with it.
- Install the fan and, if necessary, adjust its position using a special device - a potentiometer.
- Now you can start connecting additional fittings. A thermostatic valve is installed at the inlet of the pipes, and a special threaded connection is installed at the outlet. It is imperative to check the tightness of the entire structure using an air compressor.
- Now you need to connect the pipes to the heating system. This must be done in strict accordance with the project.
- Finally, you can begin to assemble and install the water convector itself. To do this, in accordance with the diagram, install the frame, grille and thermostatic head, and attach the walls of the radiator.
- Using special adjusting screws, calibrate the location of the device on the wall, focusing on the level.
In principle, the installation of a built-in underfloor water convector is carried out in approximately the same way. Only first, when performing a rough screed, special built-in boxes are made in the floor, into which the radiator itself will later be placed.
Without any skills, it will be quite difficult to install such a water heating convector yourself for the first time. Therefore, here you either need to call a specialist, or be patient and act as carefully and slowly as possible.
Advantages of this type of heating
Insulating walls with “warm electric floors,” like any heating, has its pros and cons.
- It is not possible to place furniture near heating walls. It will prevent the spread of heat, in addition, hot air will have a negative effect on the products, which will ultimately shorten the service life.
- You cannot hang a picture or TV on such a surface, as this could damage the heating elements.
- Large heat losses occur. After all, the wall is heated, on the other side of which there is a street, resulting in unnecessary consumption of thermal energy.
- Shifting the dew point deeper into the wall. In winter, condensation will accumulate, which will lead to freezing, and this will accelerate the process of destruction of the walls.
- Increased electricity consumption.
- Destruction of the finishing - the service life of wall coverings will be significantly less than on walls without heating.
As you can see, there are many disadvantages, although one cannot help but mention the positive aspects of such heating:
- located vertically, so dust will not spread throughout the room;
- will free up space in the room that is occupied by standard radiators;
- cost-effectiveness in terms of installation - installation is inexpensive compared to installing another heating device;
- creates an excellent thermal effect;
- fights fungus and mold;
- does not dry out the air, since there are no open elements that burn oxygen;
- heating of the room occurs more evenly;
- does not spoil the interior of the room.
Since, with electric wall heating, the heating method is radiant, you can save money by setting the temperature level in the room 2 degrees lower, which will not affect the level of comfort.
Another important point is that if a wall separates two rooms in an apartment, then if there is heating on it, both rooms will be heated.
What kind of lighting do you prefer?
Built-in Chandelier
Advantages, disadvantages
- Easy to install and operate. It comes down to three steps: remove the packaging, hang it on the wall, plug it into the socket. The controls are intuitive.
- Reliability, long service life - up to 15-20 years. Virtually no moving parts, proven designs.
- Safety - maximum heating temperature of the thermoelement is 80 degrees. Fire and serious burns are not possible. Location on the wall or ceiling reduces the risk to a minimum.
- Environmentally friendly - does not burn oxygen.
- Efficiency - up to 97%.
- You can fit the convector into any interior by placing it on the wall, ceiling, or floor.
The disadvantage is the cost of electricity needed to operate. But, due to rising prices for other energy sources, the disadvantage is less noticeable in comparison with the advantages.
Expert opinion
It-Technology, Electrical power and electronics specialist
Ask questions to the “Specialist for modernization of energy generation systems”
Warm the house and not start a fire: use and installation of electric convectors. – online store Many devices have the ability to connect a thermostat, which allows the user to more finely control the temperature in the room. Ask, I'm in touch!
Management in what cases is it necessary?
When choosing convectors with additional convection, you always need a thermostat and a transformer (current converter). Convectors with natural convection can be controlled mechanically, for example by a thermal head (5 speeds).
Choice
You need to be guided by value, purpose. Can be used as backup, main heating, thermal curtain generator in front of panoramic windows, glass walls (for example, on verandas, winter gardens, greenhouses).
The second sign is the power of the device. For 10 sq. meters of area should account for 1.2-1.5 kW of power.
It is enough to purchase 2-3 devices and place them evenly throughout the room along the external walls, under the windows. It costs less than buying one powerful device, will reduce the load on the electrical network, and will create a safety margin for the heating method. If one breaks, the room will be heated by the remaining ones.
The third important factor is additional functions. They make the device comfortable and multifunctional. The mandatory number of additions includes protection against overheating, tipping over, and short circuit. Useful: air humidifier, ionizer, forced circulation, remote control.
Convector installation
If the convector must be located on the wall, it is better to entrust the installation to specialists. They will correctly install brackets and equipment on a vertical surface.
By and large, convectors do not require special attention to themselves. The main thing is to wipe them from dust. In this case, the equipment must be turned off from the network and allowed to cool. The heater can be wiped with a dry or slightly damp cloth. Please note: under no circumstances should you use furniture polish.
Electric convector grilles can be cleaned with a vacuum cleaner, but do this no more than once or twice a year.
When removing the convector before the onset of hot summer, make sure that it will be stored in a room with as low humidity as possible. Also, do not leave the device exposed to sunlight and protect it from sudden temperature changes. Optimal storage conditions are temperature 12-27° and relative humidity 40-60%.
Expert opinion
It-Technology, Electrical power and electronics specialist
Ask questions to the “Specialist for modernization of energy generation systems”
Installation instructions for Teplokeramik ceramic heaters. Articles After a lot of thought, studying a bunch of information, buying another heater, they seem to be inexpensive, but when you buy one every year, it turns out fine, we finally decided on TEPLEKO. Ask, I'm in touch!
How to connect a thermostat?
First you need to decide what type of thermostat you want to install. At the moment, according to the installation method, they are divided into 2 types:
The wall adjuster is a little more difficult to install, but can be installed wherever you find convenient. It is enough to attach it to the wall with self-tapping screws or install it in a trim box (mounting box) and connect it to the panels. If you plan to install several panels in a room, then they are connected to each other in parallel:
That's all! There is nothing complicated about it. But still, if you have questions about installing ceramic infrared heaters, call us, we will be happy to advise you. If you do not want to install the panels yourself, then our company will do it for you, but only within Kyiv and the region.
Conclusion
Convectors belong to the category of simple, promising heating devices. For those who want to purchase and install it correctly in a house, apartment, or office, a few tips from experts will be useful:
Expert opinion
It-Technology, Electrical power and electronics specialist
Ask questions to the “Specialist for modernization of energy generation systems”
What are the features of installing a ceramic panel? Installation involves removing it from the packaging, assembling the mounting bracket, marking holes in the wall for screws, checking the parallelism of the floor with a building level, screwing the bracket, and installing the device. Ask, I'm in touch!
DIY screen for a heater
The main source of heat in our country house will be the stove.
But there will also be a heater installed in each room to maintain the optimal temperature. It is not recommended to install heaters in a wooden house next to a wall: the wood can dry out and crack, and it is also a fire hazard. If we want to hang the heater on the wall, we must first hang the screen.
We bought “reflective insulation VPE lavsan 3mm” in the Leroy Merlin store; for 5 square meters we paid 158 rubles.
