Before you disassemble your hair straightener, you need to carefully weigh your options. Despite the apparent simplicity of the device, this operation can lead to the complete unsuitability of the curling iron for further use. To produce repair rectifier designed for hair styling, you must be able to use a screwdriver and side cutters, have your own soldering iron and tester. Knowledge of radio engineering and plumbing will be useful.
How the device works
Modern curling irons on the market are distinguished by a variety of shapes and a range of functions.
But, regardless of the brand or model, they are all similar in design. The basis of the device is a round body with a heating element inside and a triangular flexible leg-stand. A power cord with a plug is connected to the handle. A metal clamp is hinged. Unfortunately, the simple design of the styler does not guarantee its reliability and trouble-free operation. Even the cheapest models of the most popular brands fail.
If you repair your hair curling iron yourself, you can save money and time that you would spend on visiting a specialist. The main thing is to correctly disassemble the device and determine the cause of the malfunction.
How to care for your iron
How to make your iron last longer. Its plates are the main working surface, with the help of which the composition is directly evaporated on the hair. With constant use, the plates become covered with particles of the compositions and styling products used, and even if you don’t see it, there will be a microfilm on the coating of the iron from the remnants of the products you used in your work.
Using an iron with uncleaned plates can lead to:
- strands sticking to the plates during work, creating a feeling of under-evaporation of the composition and the iron does not glide well enough through the hair, which makes work difficult;
- unpleasant smell of burning (burning) or excessive smoke during operation;
- uneven heating of the plates from the center to the edges, and as you know, plus or minus five degrees and the straightening result may not be ideal, because you precisely choose the temperature regime for the condition of the hair and the composition you are working with;
- may cause additional damage to the ends of the hair and, as a result, split ends and untidy appearance of the ends.
So, we have figured out that the plates need care and cleaning, let's figure out how to do it correctly.
DIY repair
Repairing a hair curler does not take much time. To repair the styler, you will need two screwdrivers (Phillips and flat head for removing plugs), a piece of electrical wire, a multimeter, and insulating or adhesive tape.
When the moving contact oxidizes, the parts must be separated. Then carefully sand both elements with very fine sandpaper.
Just in case, check the cord with a multimeter. This way you will know if there are any breaks or pinches. If such damage is found, be sure to replace the wire.
When the curling iron begins to press the hair worse, it is necessary to straighten the spring. To do this, you need to remove the retractable stand and carefully unscrew the fasteners.
Sometimes it is enough to pry the spring with a flat screwdriver or your finger - and it easily falls into place. But it also happens that you have to remove it from the body and return it to the desired position separately from the device.
After carrying out these manipulations, put the clamp in place, secure it tightly with bolts and install the lower retractable bracket-stand.
As you can see, the design of this electrical appliance is so simple that repairing it at home is not at all difficult. However, before you start repairing, you need to learn how to properly disassemble the curling iron.
Disassembly
To understand what exactly caused the curling iron to fail, you need to disassemble the device.
Models from different brands are designed approximately the same. Having learned how to repair one styler, you will successfully cope with the repair of any other device for styling curls. All tongs consist of two halves. They need to be sorted in this order:
After establishing the exact cause of the malfunction, you can proceed directly to repairing the device. Don't forget to grab the tools mentioned above right away.
Fault options
There are many reasons for a curling iron to break. However, there are a few that are most common. Let's look at the most common types of faults.
It is recommended to watch a video on how to troubleshoot a curling iron. A visual example will help you navigate faster.
| What's happened | Cause | Troubleshooting method |
| There is no power to the temperature controller board. | Wire fault. | Disassemble and carefully inspect the curling iron. Check the soldering of the cord to the board. If it is torn off, you need to cut off the damaged part and solder the wire in place. A broken connector is quite difficult to repair. It is recommended to exclude it from the circuit by soldering the cord directly. |
| Of the two halves of the tongs, only one works. | Soldering errors or broken heating element. | Disassemble the heating element. These are 2 plates with a resistor between them. Be especially careful with the conductive layer. We must not allow it to be erased. The malfunction is eliminated by ensuring contact of the wire with the heater plate. |
| The device does not heat up when full power is supplied to the board. | Poor soldering or burnt part. | Inspect the board. If nothing suspicious is observed, “ring” all the elements in turn. Start with the fuse. Most often, diodes and a quenching resistor are responsible for blowout. Don't forget to pay attention to the capacitor and variable resistor (if you see the latter in the diagram). |
Have you completed all the manipulations, but the device still does not work? Then it’s better to contact a specialist. Repairs may require special skills or tools.
Repairing the swivel
The purpose of the swivel is to rotate the styler. If used improperly, the wire may become severely twisted. As a result, a break occurs at the point where it is attached to the body.
You can repair the cord by insulating the exposed part. However, such repairs will be short-term. Often he threatens with electric shock in the future.
To properly repair a swivel, you need to do the following:
If you did everything correctly, the styler will function as before. If suddenly it doesn’t work out, it’s okay. Take the curling iron to a workshop and let an experienced specialist handle it.
Replacing the heating element
If your styler suddenly stops working, immediately check to see if the wire is damaged. The curling iron turns on normally (the indicator light comes on), but does not heat? Apparently, the heating element is to blame, which most likely burned out.
Here's what you need to do to replace a damaged part:
Assemble the styler step by step and plug it into the network. If you managed to replace the heating element successfully, the device will fully restore its functionality.
Possible breakdowns and solutions
- There is no power on the temperature controller board - the cord is faulty. It needs to be inspected and the soldering to the board checked. If a break is detected, the damaged part is cut off and the cable is soldered in place. A faulty connector is difficult to repair, so you can simply exclude it from the circuit and solder the cord directly.
- Only one half of the tongs works - the tenge is broken or the soldering is bad. Eliminated by disassembling the heating element. It represents two plates with a resistor between them. When disassembling, special attention must be paid to the conductive layer so that it is not accidentally erased. Troubleshooting comes down to ensuring contact between the wire and the tena plate.
- Power is supplied to the board, but the hair iron does not heat up - poor-quality soldering, burnout of one of the parts. The board is being inspected. If there are no visible defects, all elements are called sequentially, starting with the fuse. The most common failures are the quenching resistor and diodes. Particular attention should be paid to the capacitor and variable resistor (if provided schematically).
As you can see, it is quite possible to repair a hair straightener yourself. However, we should not forget about electrical safety rules and restore the device only when disconnected from the network.
Rating of the best curling irons
Knowing how to disassemble your curling iron and repair it yourself will extend the life of the device. And this is certainly a positive thing. However, in order to avoid repair work or at least minimize it, you should initially try to choose a high-quality styler.
Today, the beauty device market is replete with a huge number of models that can give curls a wide variety of shapes. Small and large curls, Hollywood curls, corrugations - this is not a complete list of styling.
There are also curling irons on sale that do the gripping and twisting of the strands themselves. Technological progress does not stand still. Manufacturers are doing everything possible to improve the convenience and modernize the functionality of stylers.
When choosing a device, first of all you need to pay attention to the brand. This is the most important criterion. The more serious and well-known the company, the longer the purchased curling iron will last and the better the curl will be.
Among the leaders in the rating are the following brands:
Stylers from the listed manufacturers can probably be seen in any home appliance store. They cannot be considered cheap. And yet they are in high demand.
In addition to the brands mentioned above, there are also professional curling irons that are sold only in specialized outlets. If you believe the reviews, the best among them are:
Of course, the latest devices are more expensive. True, they compensate for the costs with their endurance and long service life.
Let's sum it up
To prevent suddenly broken curling irons from ruining your hairstyle and mood, you need to take the choice of this device very seriously. But since purchasing even the most expensive styler does not guarantee its eternal operation, it is better to immediately acquire the tools necessary for repairs.
Do not try to disassemble the iron after purchase. Firstly, it will still be under warranty. And secondly, there is a risk that you will not put it back together. And instead of a brand new device, you will receive a non-functional set of parts. It’s another matter if the styler is already broken - in this case, you definitely have nothing to lose.
If you cannot repair the tongs yourself, do not hesitate to seek help from a specialist. After all, the main thing is a functioning device, and not who repaired it.
Source
Hair curler malfunction
The problem appeared after the device fell from the cabinet onto the floor. It manifested itself in the fact that the hair straightening attachment did not press the strands, thus the desired effect was not achieved.
When you pressed the lever with your finger, the upper part of the electric forceps was lifted, but did not return to its original state. It was clear that something was wrong with the return spring.
But getting to the spring turned out to be not so easy. To do this, it was necessary to disassemble the entire structure. Here's how to do it. Remove the nozzle from the handle by turning the clamping ring.
The hair curler does not heat up, what should I do?
_________________ Don’t interfere! WITH." Why doesn’t the Lord give us a helping hand for so long? And the worst thing is: maybe he’s holding out, but we don’t notice it longer and longer?”
Register and receive two coupons for $5 each: https://jlcpcb.com/cwc
| Chainik |
| jib |
| We invite everyone to attend a webinar on Fanso lithium power sources (EVE) on November 30th. You will learn about the features of using lithium power supplies and how they are affected by operating mode and operating conditions. We will tell you what parameters are important to consider when choosing a lithium HIT, consider the pitfalls that you may encounter if you make the wrong choice, and discuss how to properly conduct tests to ensure the reliability of the final solution. You will be able to ask questions to manufacturer representatives who will participate in the webinar. | ||
| Chainik | Analogue temperature sensor KTY83/110.153 (NXP) DO-34 We invite everyone to attend a webinar dedicated to Ethernet technology and its new 10BASE-T1S/L standard. The 802.3cg standard describes data transmission at speeds of up to 10 Mbit per second over a single twisted pair cable. The webinar will also discuss other innovations that have recently entered the Ethernet family of technologies: Synchronous Ethernet (SyncE), Precision Time Protocol (PTP), Time Sensitive Networking (TSN). High-speed 25G+ Ethernet from Microchip will not be left out either. |
| jib |
| Page 1 of 1 | [Posts: 6] |
Time zone: UTC + 3 hours
Who's on the forum now?
This forum is currently viewed by: no registered users and guests: 5
Source
Keratin hair straightening in the salon
A salon procedure for straightening unruly or frizzy locks is becoming increasingly popular. The process takes several hours, but the effect lasts from 3 to 5 weeks, depending on subsequent home care and the initial hair structure. In addition to smoothness, the curls receive nutrition, become healthy and shiny. The before and after results can be seen in the photo; the differences become noticeable immediately.
The cost of keratin straightening is quite high; specialists charge from 2 to 5 thousand rubles for one procedure. The whole technique consists of washing your hair with a special cleansing shampoo, applying a keratin composition with silicone, securing the result with a restorative spray and conditioner.
Keratin straightening with a lamination effect can be done even at home. This is explained in detail in a clear training video.
Source
DIY hair straightener repair
Before you disassemble your hair straightener, you need to carefully weigh your options. Despite the apparent simplicity of the device, this operation can lead to the complete unsuitability of the curling iron for further use. To repair a straightener designed for hair styling , you must be able to use a screwdriver and side cutters, have your own soldering iron and tester. Knowledge of radio engineering and plumbing will be useful.
Recommendations and precautions
Following several recommendations helps slow down the appearance of plaque on the surfaces of the iron:
- If possible, use a straightener on clean hair without any residue from hairspray or other cosmetics.
- The iron plates get less dirty when using high temperatures, since you have to run the device through the curls less.
- You need to straighten your hair after thoroughly combing it so that the strands come into contact with the heated surface evenly.
When cleaning, precautions must be taken. First of all, you cannot use certain products and materials to remove plaque.
Namely:
- any cleaning and washing powders, they can leave scratches;
- metal blades, pins, paper clips and needles;
- abrasive iron scourers for dishes;
- bar soap.
It is also prohibited to use kerosene and gasoline to clean the iron. These are good solvents, but their microscopic residues on the surface of the plates can ignite during subsequent heating of the device.
The iron cannot be cleaned with acidic sanitary ware; they harm the coating of the plates.
Design and principle of operation of the device
A hair straightener is a heating clip-style device that allows you to straighten stubborn curls. Leveling is ensured by a temperature of 120º to 210ºC, which is formed between two tightly adjacent, smooth plates. They press strands of hair under the influence of a spring.
Despite the wide variety of brands and models of curling irons, they are all basically similar in layout. The hair straightener circuit includes:
Unfortunately, the simplicity of the device design does not lead to its reliability. Even models from well-known manufacturers often fail. Repairing your hair straightener yourself can save you money and time spent going to a hair repair shop.
Advantages and disadvantages
The advantages of Bosch rectifiers have already been appreciated by many customers:
- Stylish and compact design . The brand's irons are pleasant to hold, they are easy to use and take their rightful place on the dressing table. In addition, any of the straighteners can be taken with you on trips; it will not take up much space in your bag and will add almost no weight to it.
- Possibility of temperature adjustment. You determine the level of heat required for your hair. For those with colored, thin or damaged strands, temperatures above 150° C are not recommended. Normal hair types can withstand temperatures up to 180° C. If you have coarse hair, you may need maximum heating to achieve the ideal effect. The required temperature also depends on how naturally curly the hair is.
- Ionization . A special layer covering the plates of the device releases negative ions when the temperature increases. They, in turn, restore the water balance of each hair, creating the visual effect of silky and well-groomed curls.
- Durability . Anodized plates are resistant to damage and retain their original appearance and properties for a long time.
- Variety of models. Among the brand's assortment you can find a small iron with a minimal set of functions and a universal device for smoothing and curling hair. With this device you can change your looks and always look amazing.
Some buyers can name only the expensive cost of the brand’s products as a negative nuance.
Do-it-yourself troubleshooting
Hair straightener failure may result in partial or complete loss of heat or mechanical failure. Before disassembling the iron, you should carefully inspect it for integrity.
The most common problem with these devices is a broken power cord. In models with a detachable wire, the fault lies in poor contact of the connector.
Disassembly begins with separating the halves of the iron. To do this, remove the decorative plugs on the sides of the device and unscrew the tightening screw.
Attention: This operation must be carried out carefully, since there is a spring on the axis connecting the parts of the curling iron. Before removing, you need to note its exact location so as not to waste time and nerves during assembly.
When the halves are separated, access will be made to the remaining screws securing the covers that cover the shadows and controls. Having gained access to the temperature regulator, you can begin to inspect and test the parts.
How to disassemble a hair dryer: inspection procedure, disassembly and repair
Disassembling the device is not difficult if you follow the instructions, have the necessary tools on hand and have at least some knowledge in the field of electronics.
Cord
First of all, you need to inspect the wire. You should start with a power outlet to make sure there is electricity. If there is light, then move on to checking the cord - from the body to the plug. Inspect the integrity of the wire, look for kinks, breaks, melting. Inside the case, after disassembling it, observe the state of the electrical resistance - a pair of detachable contacts, soldering or wiring with plastic caps.
Permanent connection
If the wiring is embedded in plastic caps, then we are talking about a permanent connection. This option is quite difficult to test and requires the following materials:
- regular needle;
- tester;
- lamp;
- indicator.
The check is performed as follows:
- A needle is attached to one terminal - it should be inserted into the power core near the cap all the way to the copper;
- The second terminal covers the antennae of the plug;
- Both wires ring at once.
Healthy!
You should not make more than one puncture per core, since the operation of the device does not exclude moisture from entering the housing.
Contact pad
It is much easier to ring the wire when the joints are visible to the naked eye. If damage is found, it is better to replace the cord with a new one that has a permanent plug. The second option is preferable, since in the first case restrictions are imposed on the choice of insulating materials that prevent moisture from entering the cores.
Attention!
The most vulnerable spot is at the contact of the wire with the body. Constant bending and twisting of the cord leads to chafing and cracking. Damaged copper strands begin to spark, burn electrical tape and melt.
Switch and switch
You can check the functionality of the switch by short-circuiting the part. If a three-position switch is used, the corresponding check will need to be performed three times - for each mode separately. It is better to sketch out the wiring diagram to avoid mistakes during assembly.
Once a defect is identified, it should be carefully inspected and processed. Burn marks should be cleaned off with a file, eraser or sandpaper, contacts should be treated with alcohol. If an element cannot be restored, it should be replaced with a new, similar one.
Fan
A clogged air duct is a common problem when operating equipment. If there is a filter, it must be removed and thoroughly cleaned; clogged dust can be removed using a soft brush. If you find hair wound around the motor axis, it is better to remove the fan from the shaft and then remove the dirt.
Spirals
Most often, devices are equipped with several heaters at once, which outwardly do not differ from each other. After disassembling the unit, you should make sure that the heating elements are identical; if there are breaks, they need to be soldered or the ends twisted. In addition, the ends of the spiral can be connected using thin copper tubes.
Engine
A breakdown of the motor is indicated by the occurrence of a strong crackling sound and the presence of sparks when turned on. If a malfunction is detected, remove the motor winding from the electrical circuit and check all connections. Replacing the winding requires certain skills and knowledge in the field of electrical engineering, so if you don’t have them, it’s better to immediately turn to professionals.
Healthy!
If the winding is in good condition, it is enough to clean the surface and evaluate the tightness of the brushes to the copper surface. In this case, the shaft should rotate freely, and it is better to lubricate all rubbing elements.
Chip:
- The getinax substrate periodically cracks, which leads to rupture of the track. If a damaged fragment is found, it should be buried, covering it a little with solder;
- A malfunction of the capacitor is indicated by swelling of the product; if it breaks, it bends outward. If a breakdown is identified, the only way out is to replace the part with a new one;
- When the resistor burns out, it darkens. Even if it is not faulty, it is worth replacing.
Thermostat
Some models are equipped with a self-regulation function. Operation is carried out by using a resistive divider, in which one arm is responsible for responding to temperature. In the future you can proceed as follows:
- Eliminate the sensor by breaking the circuit, and then check its functionality.
- Close the wires and observe the reaction of the device.
There is a high probability that the attempt will not be successful if the device only responds to certain resistance values.
Who can repair their hair curling iron themselves?
First, it should be noted that fixing a curling iron is quite a serious matter, requiring skills in repairing electrical appliances. If you basically understand the repair of electrical equipment, have experience in such repairs and have the necessary tools - an electrical tester and a soldering iron, at a minimum - then you can cope with this. You won't find anything super complicated or super specific here.
But if you do not have the necessary skills and do not have the necessary equipment, it is better not to get into the inside of the iron, because you may not only not achieve results, but also create new problems, further complicating future repairs for those who will do it.
What exactly breaks in a hair straightener - and how to fix it?
The main symptom is a complete loss of heat; the iron does not respond to your actions at all. Generally speaking, this is probably the most common problem that occurs with hairdressing electrical equipment. And with basic skills and equipment, it’s the easiest to fix.
In any case, the iron will most likely have to be disassembled, for which you first need to remove the decorative plugs, then unscrew the main tightening screw between the halves - be careful, watch how the spring is installed when unscrewing it, so that you can return it to its place without any problems. Then calmly unscrew the halves and look where the cord is connected.
A very common option is that the cord is basically fine, but the problem arises at the soldering point to the board. If the tester shows that there is current on the cord, but not in the curling iron, try re-soldering the cord.
There is also the possibility that the cord is damaged somewhere along the length. It is necessary to ring the cord with a tester and find the break point. The damaged part is cut off, and the working part is soldered back.
This problem is the most common. But it is also possible that one half of the curling iron heats up, but the other half does not. In this case, it also makes sense to first ring the elements of the curling iron with a tester and check the soldering. It is necessary to restore contact between the electrical wire and the heating element.
The internal elements of the curling iron can also burn out - often these are diodes or a quenching resistor. If the power supply is checked and everything is absolutely fine with it, but the curling iron, nevertheless, does not work, it makes sense to sequentially check all the internal elements of the circuit, starting from the fuse, and find the element that requires replacement.
Of course, I would like there to be as few problems as possible with the curling iron, so that it does not break for as long as possible. Anything can happen, of course, but it largely depends on the quality of the elements of the curling iron and the quality of its assembly. If your current curling iron does not suit you with its performance, often breaks or does not perform its functions well, pay attention to professional-grade curling irons from Mustang, which you can choose from our catalog.
How to disassemble a Philips hair dryer?
Sometimes after an unsuccessful fall or after another mechanical impact, this device stops working. A wonderful way out of this difficult situation would be to completely disassemble the hair dryer. Do you want to know how to disassemble a hair dryer? There is nothing complicated about this, the main thing is to follow the steps of the instructions.
The first step is to disassemble the case. For most models (for example, rowenta pro 2300 and braun 3536), it opens into two identical halves. To comply with safety regulations, be sure to unplug the electrical cord from the outlet before unscrewing the screws.
Typically, the body of the device is held on by simple metal screws. They can be with non-standard heads in the form of a plus sign, a pitchfork or an asterisk. Therefore, before disassembling the Philips hair dryer, you will need to make sure that you have the necessary tools.
After opening the device, you will find the internal mechanisms of the device that are responsible for its smooth functioning. If the hair dryer breaks down, the cause of the breakdown will be hidden in these parts. In addition, some models have additional fastenings in the form of latches and hidden screws hidden under decorative overlays.
Do you want to know how to disassemble the philips salondry control hair dryer? To do this, you need to familiarize yourself with its internal structure and carefully inspect all the details. The most common failure of many devices is a damaged power cord. If there are burnt parts or kinks, it will be necessary to re-solder it.
The main internal element of any hair dryer is the fan. It is driven by an electric motor and draws air through a special opening with a grille. In some cases, the breakdown of the device is associated with its contamination, so if there is dust, it should be thoroughly cleaned.
The air passes through the heating element - a wire that is wound on the thermostat. It should have a solid appearance. If there are breaks, the spiral parts should be twisted or soldered. Some models (for example, babyliss pro) are also equipped with a limiter that prevents the device from sucking in long hair and other fibers along with the air. It can also become clogged if the device is not working properly.
If you hear a crackling sound and see sparks when you turn on the device, this indicates a motor failure. This problem can be solved by replacing the copper windings and diode bridge. However, it is difficult to carry out such repairs at home, so in this case you should contact a workshop.
Do you want to know how to disassemble the rowenta brush activ 1000 hair dryer? The design of this device has several nuances compared to a conventional hair dryer. In order to inspect the internal elements and mechanisms in the event of a breakdown, you need to perform a few simple steps:
- Remove the plastic attachment from the front of the device, as it will interfere with disassembly later. To do this, it must be smoothly moved left and right until it is completely disconnected from the device;
- When removing the plastic ring, it is not recommended to use screwdrivers or other tools, as they can damage the case and leave visible scratches on it;
- Afterwards, you need to remove the rear mesh attachment, which interferes with disassembling the device. However, you should not apply a lot of force, as this may lead to its breakage;
- Modern models of hair dryers of many brands (Roventa, Remington, Scarlet and others) do not have metal bolts on the body. The two parts of the hair dryer are secured using latches. To separate them, the two halves of the housing should be pulled away from each other while rotating.
So that you do not have to repair household appliances yourself, you need to buy a good hair dryer
Which one to choose from all the variety on the market? Before purchasing, you need to pay attention to the reputation of the brand, since only well-known manufacturers produce quality products. Other selection criteria are power, number of operating modes, cold air function
We have told you about the main features of the internal structure of the hair dryer, so you should not have any questions about how to disassemble the Roventa Brush Active hair dryer and other brands. However, remember that when repairing small household appliances yourself, you should follow safety rules and be sure to remove the power cord from the outlet.
What to do if your hair straightener doesn't heat up?
Last edited by Alex-GT Tue Feb 26, 2013 10:26:37 AM, edited 1 time in total.
| Cat's friend |
Karma:
9
Message rating:
61
Registered:
Sat Nov 07, 2009 11:45:42
Messages:
4348
Message rating:
0
Register and receive two coupons for $5 each: https://jlcpcb.com/quote
| Cat's drinking buddy |
Karma:
8
Message rating:
126
Registered:
Wed Sep 28, 2011 22:18:14
Messages:
2976
From:
Moscow
Message rating:
0
_________________ People can live without brains.
Wolfspeed offers discrete silicon carbide diodes manufactured using JBS and MPS technologies, with maximum permissible voltages of 600 V, 650 V, 1200 V and 1700 V and maximum current from 1 to 50 A. A distinctive feature of all models is the low charge value shutter and high overload capacity.
BlueNRG-LP is STMicroelectronics' new programmable SoC chip. It complies with the BLE specification version 5.2, supports Bluetooth Mesh networks, and is suitable for wireless communication at a frequency of 2.4 GHz. The new chip has high performance.
| Cat's drinking buddy |
Karma:
8
Message rating:
126
Registered:
Wed Sep 28, 2011 22:18:14
Messages:
2976
From:
Moscow
Message rating:
0
_________________ People can live without brains.
| Cat's drinking buddy |
Karma:
8
Message rating:
126
Registered:
Wed Sep 28, 2011 22:18:14
Messages:
2976
From:
Moscow
Message rating:
0
_________________ People can live without brains.
PRIST expands its range
| Cat's friend |
Karma:
52
Post rating:
846
Registered:
Tue Sep 07, 2010 03:01:06
Posts:
16548
From:
Moscow-Izmaylovo
Post rating:
0
You can't get the firmware from this MK; it's locked. But it definitely has nothing to do with it - firmware and microcontroller. This styler . The wires there are crappy, as are the contacts.
You can connect these heaters through a 220 light bulb and check their functionality.
_________________ I'm going to WWW treat your crippled equipment.
You can't get the firmware from this MK; it's locked. But it definitely has nothing to do with it - firmware and microcontroller. This styler . The wires there are crappy, as are the contacts.
You can connect these heaters through a 220 light bulb and check their functionality.
Heaters are OK. We tested and retested. The wires are ringing, bent this way and that.” Is there 5v on the lite? — the MK should work from external power.” How do you understand this? What is lit? I don’t quite understand some of the abbreviations
With R18 everything is fine. It’s something like glue on the board. It doesn’t conduct current and doesn’t interfere with life. The zener diodes and diode are in perfect order. Up to the semmistor, the circuit is absolutely working. All problems are on the control power supply.
| Cat's friend |
Karma:
52
Post rating:
846
Registered:
Tue Sep 07, 2010 03:01:06
Posts:
16548
From:
Moscow-Izmaylovo
Post rating:
0
The R18 you have - judging by the picture - should not work at all - the scalp has been removed from it - remove it at an angle of 45 degrees in an enlarged format.
Measure it with a toaster - no better tester - multimeter - ohmmeter
_________________ I'm going to WWW treat your crippled equipment.
| Cat's friend |
Karma:
27
Message rating:
458
Registered:
Sat Nov 20, 2010 21:54:31
Messages:
3567
Message rating:
0
| Cat's friend |
Karma:
27
Message rating:
458
Registered:
Sat Nov 20, 2010 21:54:31
Messages:
3567
Message rating:
0
| Cat's friend |
Karma:
52
Post rating:
846
Registered:
Tue Sep 07, 2010 03:01:06
Posts:
16548
From:
Moscow-Izmaylovo
Post rating:
0
give it five volts, I would have done it long ago
If there's a hell of a lot on it, then you're not getting power to it - there's a broken wire or stabilizer.
_________________ I'm going to WWW treat your crippled equipment.
give it five volts, I would have done it long ago
If there's a hell of a lot on it, then you're not getting power to it - there's a broken wire or stabilizer.
| Cat's drinking buddy |
Karma:
8
Message rating:
126
Registered:
Wed Sep 28, 2011 22:18:14
Messages:
2976
From:
Moscow
Message rating:
0
_________________ People can live without brains.
| Cat's drinking buddy |
Karma:
8
Message rating:
126
Registered:
Wed Sep 28, 2011 22:18:14
Messages:
2976
From:
Moscow
Message rating:
0
_________________ People can live without brains.
